CV. KEIHIN & BUTTERFLY
299,-
Modellnummer: 27006-88
Merke: MCS
Rebuild kit for all OEM Keihin CV (Constant Vacuum) carburetor variations as used on XL Sportster and Big Twin models. Replacement reference 27006-88. Fits: > 90-06 B.T.; 88-06 XL. With OEM 40mm CV carburetor (NU)
139,-
Modellnummer: 27371-76,
Merke: MCS
FULL BRASS Fits: > 76-06 B.T.; 76-06 XL(NU) (WITH KEIHIN CV & BUTTERFLY CARBS) IMPORTANT NOTICE Before installation carefully remove the old fuel inlet fitting from the Keihin butterfly or CV carburetor. Fuel inlet fittings have a push-fit installation, without any sealing agent between carburetor and fuel inlet fitting. The new 904816 fuel inlet fitting is slightly larger than stock to overcome machining tolerances in the stock carburetor. Please measure the old fuel inlet fitting and compare the diameter to the new fuel inlet fitting. The installation attempt of a too large fuel inlet fitting can result in a cracked carburetor housing. Correcting fuel inlet fitting size, before installation, can be done by using some fine grid waterproof sanding paper. Always make sure the new fuel inlet fitting is the correct size before final installation!
2.849,-
Merke: MCS
Quality reproduction of the 40mm Keihin Constant Vacuum with accelerator pump. This is the most frequently used carburetor in the V-Twin industry and a great solution for many stock and custom applications. Comes with a 185 main jet and 45 slow jet installed. All parts are interchangeable with OEM except the throttle cable bracket. Note: This carburetor is designed for vacuum operated petcocks. It is therefore, like late-model OEM CV carbs, not equipped with a floatbowl overflow system Fits: > Univ.
159,-
Merke: CVP
CVP, FLOAT BOWL SCREW KIT FOR KEIHIN CV. STAINLESS ALLEN Stainless allenhead kit for Keihin CV carburetors. Incl. socket head wrench. Used to mount the float bowl to the carburetor housing. These allenhead (sockethead) screws allow much better access than the OEM phillips screws. Replacement for 27579-88A OEM Phillips head screws. Fits: > 90-06 B.T.; 88-06 XL. With CV carbs (NU)
329,-
Merke: CVP
Basic kit for routine maintenance; Incl. Pump diapragm 27361-76A, float needle valve with viton rubber tip 27866-78A, floatbowl gasket seal 27577-92; Note: Will not fit early 88 -91 H-D models with CV carbs Fits: > 92-06 H-D with 40mm CV carbs (NU)
379,-
Modellnummer: 59-432-PB
Merke: DRAG SPECIALTIES
DRAG SPECIALTIES FLANG KIT CHR INT 86-05Replacement intake manifold seals also available Chrome flanges replace the stock flanges Brand DRAG SPECIALTIES Vendor part number 59-432-PB Base Finish Chrome Oem27009-86A 27010-86A Product Name Flange Intake Type Single Bore Units Set
332,-
Modellnummer: 940553
Merke: MCS
Fits: > 76-89 B.T.; 76-87 XL (NU) (EXCL. CV CARBS)
459,-
Merke: CVP
Provides a finer mist spray, which improves pick-up. Also promotes a more laminar, smoother, flow in the carburetor inlet, reducing unwanted turbulence. Includes stainless floatbowl bolts and washers. Fits: > 90-06 B.T.; 88-06 XL (NU)
79,-
Merke: JAMES GASKETS
JAMES, FLOAT BOWL TO CARB BODY SEAL. KEIHIN CV Rubber float bowl seal used between carb body and floatbowl. OEM replacement reference 27577-92. Fits: > 92-06 B.T.; 92-06 XL. With OEM Keihin CV carburetor (NU)
63,-
Modellnummer: 27582-88.
Merke: MCS
Fits: > 90-06 B.T.; 88-06 XL
131,-
Modellnummer: 27371-76A.
BRASS/PLASTIC Fits: > 76-06 B.T.; 76-06 XL(NU) (WITH KEIHIN CV & BUTTERFLY CARBS)
528,-
Merke: CVP
CVP, premium CV carburetor rebuild kit Contains all of the vital seals and gaskets needed to rebuild the 40mm Constant Vacuum carburetor. Includes: 27361-76A pump diaphragm, 27362-76 diaphragm spring, 27866-78A floatbowl needle valve, 27360-76 o-ring acc pump housing, 27157-89 o-ring drain screw, 27121-89 o-ring pump jet, 27311-76 pump boot, 27577-88 & 27577-92 floatbowl gasket seal, 27002-89 intake seal, 2x 26995-86B intake seals. - Includes early & late floatbowl seals - Premium quality seals. Fits: > 90-06 Big Twin; 88-06 XL Sportster. With OEM 40mm CV carburetor (NU)
116,-
Modellnummer: 50-8013
Merke: S&S
S&S, CARBURETOR TO MANIFOLD O-RING. SUPER B Fits between carb and manifold and/or manifold spacer block. Fits S&S Super B & 1-3/4 or 1-7/8 S&S L-series carbs. Fits: >
328,-
Merke: WANNABE CHOPPERS
sand-cast aluminum; un-polished finish; installs to carb top cover; allows easy acces to choke knob Fits: > 88-06 H-D & all customs with H-D Keihin CV carb
Utsolgt
909,-