Chrome. 1/4-20 threaded. Used to mount the rear section of your seat to the rear fender in most stock or stock-like applications.
Fits: > 96-20 most H-D
Use for custom seat mounting or replacing OEM parts
1/4"-20 die-cast nut with nylon retaining washer
DS-490044 replaces the "E" clip on DS-490045
pris pr stk
A great idea for quickly removing any seat
Chrome-plated, aluminum knob with knurled edge comes with one 1/4"-28 stud and one 1/4"-20 stud for mounting seats on various models
An O-ring at the base ensures a tight fit
Chromoly. Setebrakett er investeringsstøpt stål, rammetappen er laget av svart galvanisert 4130 kromolystål. Passer monteringsknaster på de fleste solo seter. Pivotbraketten er uferdig slik at den kan sveises til rammens ryggrad uten spesielle forberedelser. En medfølgende grad-8 unbrakonhette skulderbolt trers inn i motsatt side av braketten, og skaper en effektiv og holdbar hengselspinne.
A great idea for quickly removing any seat
Chrome-plated, aluminum knob with knurled edge comes with one 1/4"-28 stud and one 1/4"-20 stud for mounting seats on various models
An O-ring at the base ensures a tight fit
Black with black seat panels. Genuine leather upholstery. Manufactured with a sturdy steel black powder coated base plate with 6cm thick foam padding for a good combination between looks and comfort. The dual seat panels give it a sniff of 1910's racing flavor. Dimensions approx.: 12-1/2" (31.8cm) long x 10" (25.4cm) wide x 6cm thick. Note: Mounting studs A=22.5cm, B=23cm.
Fits: > UNIVERSAL
Chrome, with zinc plated hardware. Required to install detachable side plates, which are required for the installation of a sissy bar upright. Note: See (online) catalog for correct detachable side plate kits and sissy bars.
Fits: > 06-17 FXD, FXDC, FXDL, FXDSE; 06-08 FXDB (NU). Without saddlebags
Made From 9/16" steel bar
Side plates must be purchased separately
Made in the U.S.A.
For show use only, not designed for passenger support
Fits all H-D side plates except for Plug-N-Play
Black, Powder-Coated
Round Bar
Height
457 mm (18")
Width
170 mm (6-11/16")
Black. Used to install a sissy bar / hand rail. The 'width' of the installed side plates is the required width of the sissy bar upright legs/bars, measured outside to outside. Note: If a Turn Signal Relocation kit is required or not is depending on model and saddlebag configuration. When accessory saddlebags are installed it may be required to relocate the rear turn signals. Note: Dimensions are approximate and for reference only.
Fits: > 96-01 Dyna (excl. FXDWG; 00-01 FXDX/T): 6-3/4" (17.1cm) wide. 02-05 Dyna (excl. FXDWG): 7.5" (19cm) wide.
10" wide. Foam. This Up-Front version moves you 2-1/2" closer to the handlebars, when compared to the standard Bare Bones solo seat. the seat height is lowered for better control. A definite advantage for shorter riders. The Bare Bones solo seats are designed to look as thin and narrow as possible, even lower than the Silhouette solo. This gives an unbelievably sleek, low profile. Will complement the lines of every bike from stock factory to radical custom.
Fits: > 00-07 Softail FXSTD Deuce (NU)