TOOLS (Verktøy)
119,-
Merke: LISLE
Used on high energy electronic or points ignition systems. Comes with a tapered edge for measuring gap. Gapping is done with center hole that will allow you to gap spark plug without pressure to center electrode. Measures and gaps from 0.020" to 0.100" (0.5mm to 2.53mm).
116,-
Merke: MCS
1/4 DRIVE; USED TO MOUNT 910443 BRAKE PAD PIN KIT Fits: > 00-07 B.T.; 00-03(NU)XL; 02-05(NU)V-ROD (EX. L88-07 FRONT SPRINGERS)
314,-
Merke: LANG
For external threads. 6-pc UNC (coarse threads). Incl. 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, 9/16"-12. Used to restore damaged external threads. This are special threaded restoring dies that ensure a good result and they are safer in restoring threads than using regular thread cutting taps and dies. Regular cutters are sharper and can easily further damage existing threads. Packed in a re-usable clamshell package. USA made. Note: Not suitable for cutting new threads.
Utsolgt
309,-
Merke: LANG
For external threads. 6-pc UNF (fine threads). Incl. 1/4"-28, 5/16"-24, 3/8"-24, 7/16"-20, 1/2"-20, 9/16"-18. Used to restore damaged external threads. This are special threaded restoring dies that ensure a good result and they are safer in restoring threads than using regular thread cutting taps and dies. Regular cutters are sharper and can easily further damage existing threads. Packed in a re-usable clamshell package. USA made. Note: Not suitable for cutting new threads.
234,-
Modellnummer: 907375
Merke: MCS
amerikanske størrelser. 3-delt sett. Inkluderer 7/16, 1/2, 9/16, 5/8, 11/16 og 3/4 tommer. Buet skiftenøkkel med rette hoder. for bedre tilgang til hodebolter, sylinderbase og andre muttere som er montert på 'vanskelige' steder. Passer til: > Univ.
713,-
Merke: CRUZTOOLS
Roadside tool kit with small outside dimensions that is easy to carry on-bike. Packed in polyester reinforced zip-up pouch pack measuring just 5cm x 5cm x 18cm. Includes 9/16 x 5/8 and 1/2 x 9/16 wrenches, tire pressure gauge, 140mm pliers, 5-1 screwdriver set, 5/8 x 3/8 spark plug socket with lever. 10mm nut driver, T20, T25, T27 and T30 torx bits and 1/8, 5/32, 3/16, 1/4 and 5/16 hex wrenches. Fits: > For H-D
253,-
Merke: MCS
Used between primary chain and front motor sprocket to prevent primary movement when loosening & re-torquing sprocket & clutch nuts. Made from white POM (a polyoxymethylene polymer), an extremely strong and tough material. Fits: > 36-06(NU)4&5-speed B.T.; 57-20 XL; 87-10(NU)Buell
183,-
Merke: LISLE
US sizes. Tool dimension 1/2" wide x 3 1/2" long. 15 steel blades .002" to .025" (.051mm to .635mm). Plus one 2" steel ruler. Fits: > Univ.
Utsolgt
329,-
Merke: LIMIT
For US & Metric threads. Clearly identify the threads on your bolt in case of doubt. Measures the windings per inch (USA) or per millimeter (Metric). US 4 to 42 windings per inch (30 blades). Metric 0.25 to 6.0 per millimeter (24 blades). Fits: > Univ.
Utsolgt
409,-
Merke: MOTION PRO
Makes it easy to clean and lubricate control cables. Less mess and wasted lubricant. Works on most control cables with 4 mm to 8 mm OD housing. Seals over free spinning end fittings. Adjustable plunger insures efficient use of cable lube. Easy to use and clean. Fits: > Univ.
Utsolgt
739,-
Merke: SONIC
9-piece hex bit sockets on rail. 3/8" drive. US/SAE sizes. - 9x hex bit sockets: 1/8", 5/32", 3/16", 7/32", 1/4", 5/16", 3/8", 7/16", 1/2" - Dimensions: 204mm x 22mm x 64mm high - Weight: 442 grams Fits: >
199,-
Modellnummer: 906320
Merke: MCS
Used to grease installed tapered (Timken style) wheel bearings. Just remove the wheel and insert the wheel greaser. No need to disassemble wheel bearings or seals, only wheel axle must be removed. Works with 73-99 Timken style (tapered) wheel bearings only. Note: Will not work with 2000-up ball wheel bearings. Fits: > 73-99 B.T., (incl. Twin Cam), XL (NU)
149,-
Modellnummer: 910503
Iridium (yellow zinc) plated; Installs & removes regular spin on oil filters with 76mm diameter and 14 flats
568,-
Modellnummer: 547685
Merke: MOTION PRO
Medium carbon steel with hardened jaws; Used to hold clutch basket and final drive sprockets Fits: > 84-97 B.T.; 57-84 XL (NU)
1.655,-
Modellnummer: 979428
Merke: GEORGE'S GARAGE.
Used to drill out broken exhaust studs Fits: > 84-20 B.T.; 86-20 XL; 08-12(NU)XR1200; 87-10(NU)Buell XB
Utsolgt
929,-