Dach
65,-
Modellnummer: 71422-03.
Merke: MCS
IGNITION SWITCH DECAL. SATIN BLACK Replacement ignition switch decal for the dash. OEM style reproduction. OEM replacement reference 71422-03. Fits: > 03-13 FLT/Touring (NU)
27,-
Merke: MCS
Speedometer mount kit Used to mount large FL style speedometers. Complete as shown. OEM replacement reference 67066-76 kit, which consists of 67068-78 pin, 67070-76 rubber grommet and 67069-75 E-clip retaining ring
109,-
Modellnummer: OEM 67104-83
Merke: MCS
FX/FXR/XL SPEEDO / TACH MOUNT RUBBER Replacement rubber gasket for models equipped with metal speedo / tachometers. Without visor. Repl. for OEM 67104-83 rubber. Fits: > 83-92 FX, FXR, XL; 93-94 FXLR (NU)
110,-
Merke: MCS
Speedometer light socket Metal socket. 1 wire. Fits early style speedometers and dashes. Instrument light socket complete with light bulb. Fits speedometers, dashes and various custom applications. Fits: > 48-85 FLH (NU)
128,-
Merke: MCS
Dash light socket Plastic1. 2-wire. Fits most early dashes. Instrument light sockets complete with light bulb. Fits speedometers and dashes many custom applications.
109,-
Merke: MCS
Custom 5/16" LED indicator light. Red lens Plastic housing with stainless bezel. Requires 8mm (5/16") hole to mount. Approx. overall housing dimensions 7mm diameter x 24mm long (27mm with head). Comes with 76cm (30") pre-attached electrical wire. Fits: > Universal
109,-
Merke: MCS
Custom 5/16" LED indicator light. Green lens Plastic housing with stainless bezel. Requires 8mm (5/16") hole to mount. Approx. overall housing dimensions 7mm diameter x 24mm long (27mm with head). Comes with 76cm (30") pre-attached electrical wire. Fits: > Universal
132,-
Merke: MCS
Custom 5/16" LED indicator light. Blue lens Plastic housing with stainless bezel. Requires 8mm (5/16") hole to mount. Approx. overall housing dimensions 7mm diameter x 24mm long (27mm with head). Comes with 76cm (30") pre-attached electrical wire. Fits: > Universal
158,-
Merke: MCS
Fat Bob dash screw & nut kit. Chrome Fits applications without dash mounted choke knob, 2 and 3 light dash covers and 47-67 FL as an OEM replacement part. Replaces 71075-47 center screw, 6466 center screw washer, 71067-47 mounting base stud and 7848 locknut. Fits: > 47-67 FL & custom applications without chocke knob on the dash
2.149,-
Modellnummer: SIM-1A
Merke: DAKOTA DIGITAL
This module allows you to recalibrate OEM electronic speedometers when changing tire size, pulley, or final gearing Easy installation - simply plugs in between the pickup sensor and the stock wiring harness Allows small step corrections of less than 1 mph Correction range of 50% to 200% No power required to maintain calibration when the bike is parked Two sealed buttons allow easy resetting of the speedometer reading while the bike is in motion A must for custom builders using electronic speedometers
Utsolgt
647,-
Merke: MCS
Base plate mount kit, Cat Eye dash (47-84) For steel Cat Eye dash cover. A base plate is used to mount dash covers, speedometers and ignition switch to the gas tanks. Each base plate kit contains sockets for the dash lights, dash lights itself and mounting hardware. Note: Will not fit Evo flat side fuel tanks. Fits: > 47-84 B.T. (NU)
Utsolgt
899,-
Merke: MCS
36-46 style Cat Eye dash cover. gloss black Replacement steel dash cover. Complete with lenses and trim rubber. OEM replacement reference 71280-39. Note: Will not fit Evolution flat side tanks. Note: See 903570 for 36-46 B.T. and see 903575 base mounting kit for mounting on 47-84 B.T. models. Fits: > 36-84 B.T. (NU)
326,-
Merke: PAUGHCO
Fitments 36-47 Knucklehead, 48-65 Panhead, 66-67 FL Shovel Description Top bolt for most Big Twin models from 47-67 or custom applications where the choke wire is not routed threw the dash. Made in the U.S.A.
62,-