JAMES, EXHAUST STUDS Pris pr stk
5/16-18 to 5/16-24 X 1-11/16". Note: Exhaust studs as used in the M8 engine (OEM 10900015) are of a slightly different design, with a small protruding hex-shaped outer-end to aid initial stud-installation, but these early Evo/Twin Cam style studs will still fit.
Fits: > 84-23 B.T.; 86-22(NU)XL; 08-12(NU)XR1200; 87-10(NU)Buell XB models
Two used on FLT/Touring models. OEM reproduction replacement rubber. Note: See 945050 for replacement steel exhaust hanger bracket.
Fits: > L85-22 FLT/Touring; 1986(NU)FXRD only
Steel. Complete kit in black wrinkle finish with everything you need. Includes 2 flanges (84-03 style/17-22 style) and 2 retainers. Note: 84-03/17-22 'Early Style' steel and 04-17 'Late Style' plain aluminum exhaust flanges are interchangeable. Late Style flanges are thicker and designed to help prevent bending of the exhaust flange. All will fit all 84-up Big Twin and 86-up XL Sportster models. M8 models are equipped with the 'early style' steel flanges again.
Fits: > 84-22 B.T.; 86-22 XL; 08-12(NU)XR1200; 87-10(NU)Buell XB
Features a narrow design with a low-profile head
Secure exhaust heat wraps or can be used any place extra clamping is needed in extreme temps or conditions
Made in the U.S.A.
4 pk.
Incl. 91-09 style wire/graphite gaskets, 2 retaining rings, 4 washers and 4 zinc plated flange nuts. Note: The 84-90 /10-up style is preferred by many for better flow characteristics. Note: The 91-09 late style is a conical shaped gasket that was introduced by The Factory in 1991 and replaced, again, with the early style in 2010. Note that the early style will fit all models and is generally seen as the better gasket design.
Fits: > 84-23 B.T.; 86-22(NU)XL; 08-12(NU)XR1200; 87-10(NU)Buell XB
Sensor plug 2stk.
made from zinc plated steel. Fits 18mm x 1.50 sensor bungs. Required with non-O2 (oxygen) sensor equipped 86-up H-D models that have an exhaust system installed with stock threaded sensor plug holes. Can also be used on H-D models when O2 sensors are no longer required.
Two used on FLT/Touring models. OEM reproduction replacement. Note: See 945051 for replacement muffler hanger rubber.
66723-85
Fits: > L85-22 FLT/Touring; 1986(NU)FXRD only
EXHAUST INSULATING WRAP. 2" WIDE BLACK
Fiberglass exhaust wrap sold in 50ft. (15 meter) long rolls of 1.5mm thick material. Withstands heat up to 1200 °F (649 °C) continues, peak resistance 2000 °F (1093 °C). Cooling exhaust gasses lose velocity and scavenging effect is reduced. This insulating wrap helps to keep gas temperature high, thereby optimizing the thermal efficiency of the exhaust system which ultimately helps to get the last horses out of your engine. Wrap will also protect from exhaust burns and any exhaust blueing will no longer be visible. Note: Wrap ends are secured with metal tie-wraps. These are sold separately. Note: 30cm of exhaust pipe requires approximately 38" / 97cm (1 3/4" pipe) and 44" / 112cm (2" pipe) exhaust wrap. Based on 2" wide wrap and a wrapping overlap of approx. 1/4". Note: Material will discolor under influence of heat after installation.
Fits: >
2" diameter Drag Pipe baffle 12" long
Simple, low cost alternative to get the decibels of your drag pipe down. Great for custom baffle creations. Baffle, 12" (30.5 cm) long, made from zinc plated steel. Fits 2" (5.1 cm) outside diameter header pipes. Installs with included bolt.
PR.STK
Fits: > 2" diameter headers
1-3/4" diameter Drag Pipe baffle 8" long
Simple, low cost alternative to get the decibels of your drag pipe down. Great for custom baffle creations. Baffle, 8" (20.3 cm) long, made from zinc plated steel. Fits 1 3/4" (4.4 cm) outside diameter header pipes. Installs with included bolt.
pr stk
Fits: > 1 3/4" diameter headers.